![]() ![]() In order to re-enter normal operational model, simply remove and replace power to the device. Reboot the beacon into Direct Firmware Update mode.Ĭontact Radius Networks support for information on the procedure for firmware update or replacement. Press the Action Menu button and select DFU. In order to re-enter configurable mode for a RadBeacon X2, remove the front cover and switch the beacon power switch to OFF and back to ON.Ī beacon set in configurable mode will be configurable for up to 30 minutes or until you lock the device again. ![]() In order to re-enter configurable mode for a RadBeacon Tag, remove the front cover and press the configuration push button switch near the coin cell battery. In order to re-enter configurable mode for a RadBeacon USB, remove and restore power to the device. The Lock feature is a security precaution to limit the possibility of third party manipulation of your beacons once they have been installed and configured. Submit a valid PIN to prevent connections from remote Bluetooth 4.0 devices to the beacon configuration service. Press the Action Menu button and select Lock. Submit a valid PIN to reset the settings for your beacon to factory defaults. Reset the device to the original factory settings. Press the Action Menu button and select Reset. Submit a new and existing PIN to update the PIN for your beacon. Press the Action Menu button and select Update PIN. Bluetooth radio congestion Antennas on both transmitter and receiver Orientation of antennas Under good conditions (close range, high transmitter power), I typically see 80-90 of packets get detected by Android and iOS devices which allow you to easily count individual BLE packets. Validate the accuracy of your beacon settings by quickly verifying the ranging behavior of your device in proximity to your configured beacon. Press the Action Menu button and select Range. RadBeacon Radius Networks offers a wide range of hardware, software and proximity services designed to enable hyper-proximity, micro-location engagement capabilities and analytics in today's leading mobile apps, products and technologies. Update the measured power value with the results of your calibration activity and update your settings. Press the Action Menu button and select Calibrate.Ĭalibrate the measured power value of the beacon settings to ensure optimal proximity events and ranging. Submit a valid PIN to update the settings for this beacon. Press the Action Menu button and select Apply. Select any RadBeacon in the table to view it's detailed settings. ![]() Each beacon discovered is displayed with the following summary details Scan for nearby configurable RadBeacons by swiping down on the RadBeacons table. Once discovered, you can display each beacon's operating settings and make modifications to those settings. With the RadBeacon app you can scan for nearby configurable Radius Networks beacons. The RadBeacon app from Radius Networks requires an iOS iPhone, iPad or iPod touch running iOS 7.1 or higher and equipped with Bluetooth 4.0 capabilities. If you still aren't seeing the beacon then something maybe wrong with Bluetooth on your device and you can try clearing it's cache by turning Bluetooth off and then again.The RadBeacon™ app is the configuration utility for RadBeacon proximity beacons from Radius Networks that support Apple's iBeacon™ proximity services as well as other emerging proximity services. When you scan for the beacon, you should see it. For RadBeacon usb, remove power and restore power. If you are not seeing the RadBeacons in the app when you scan, the beacon is probably not in config mode anymore. On restart the problem should be corrected. If that doesn't fix it, try resetting your phone by holding down the sleep/wake button and the home button until the phone powers off. You should try turning off Bluetooth and then turning it back on again. Apple is aware of the problem and promising a fix. If you've cycled power to your beacon and are still unable to recognize it using the RadBeacon Config App, you may be experiencing the results of an iOS bug that affects proximity ranging. RadBeacon USB devices can be powered by any USB port or USB power supply. Re-initiating Configurable ModeĬonfigurable mode can be re-initiated for RadBeacon USB beacons by removing and restoring power to the device. No Power, No Problem Beacons are sold with a variety of power sources in mind. If you are using the RadBeacon Config App to detect and configure your beacons, and are unable to recognize or access your beacons, it is likely that this configuration window has lapsed. Once your RadBeacon USB has been plugged in, or your RadBeacon Tag has been activated, the beacon will broadcast in configurable mode for an initial window of 30 minutes. You can scan for beacons by pulling down on the table view in the RadBeacon Configuration App.ĭownload the RadBeacon Config App for your device. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |